Next: , Previous: , Up: Remote Protocol   [Contents][Index]


E.4 Stop Reply Packets

The ‘C’, ‘c’, ‘S’, ‘s’, ‘vCont’, ‘vAttach’, ‘vRun’, ‘vStopped’, and ‘?’ packets can receive any of the below as a reply. Except for ‘?’ and ‘vStopped’, that reply is only returned when the target halts. In the below the exact meaning of signal number is defined by the header include/gdb/signals.h in the GDB source code.

In non-stop mode, the server will simply reply ‘OK’ to commands such as ‘vCont’; any stop will be the subject of a future notification. See Remote Non-Stop.

As in the description of request packets, we include spaces in the reply templates for clarity; these are not part of the reply packet’s syntax. No GDB stop reply packet uses spaces to separate its components.

S AA

The program received signal number AA (a two-digit hexadecimal number). This is equivalent to a ‘T’ response with no n:r pairs.

T AA n1:r1;n2:r2;…

The program received signal number AA (a two-digit hexadecimal number). This is equivalent to an ‘S’ response, except that the ‘n:r’ pairs can carry values of important registers and other information directly in the stop reply packet, reducing round-trip latency. Single-step and breakpoint traps are reported this way. Each ‘n:r’ pair is interpreted as follows:

The currently defined stop reasons are:

watch
rwatch
awatch

The packet indicates a watchpoint hit, and r is the data address, in hex.

syscall_entry
syscall_return

The packet indicates a syscall entry or return, and r is the syscall number, in hex.

library

The packet indicates that the loaded libraries have changed. GDB should use ‘qXfer:libraries:read’ to fetch a new list of loaded libraries. The r part is ignored.

replaylog

The packet indicates that the target cannot continue replaying logged execution events, because it has reached the end (or the beginning when executing backward) of the log. The value of r will be either ‘begin’ or ‘end’. See Reverse Execution, for more information.

swbreak

The packet indicates a software breakpoint instruction was executed, irrespective of whether it was GDB that planted the breakpoint or the breakpoint is hardcoded in the program. The r part must be left empty.

On some architectures, such as x86, at the architecture level, when a breakpoint instruction executes the program counter points at the breakpoint address plus an offset. On such targets, the stub is responsible for adjusting the PC to point back at the breakpoint address.

This packet should not be sent by default; older GDB versions did not support it. GDB requests it, by supplying an appropriate ‘qSupported’ feature (see qSupported). The remote stub must also supply the appropriate ‘qSupported’ feature indicating support.

This packet is required for correct non-stop mode operation.

hwbreak

The packet indicates the target stopped for a hardware breakpoint. The r part must be left empty.

The same remarks about ‘qSupported’ and non-stop mode above apply.

fork

The packet indicates that fork was called, and r is the thread ID of the new child process, as specified in thread-id syntax. This packet is only applicable to targets that support fork events.

This packet should not be sent by default; older GDB versions did not support it. GDB requests it, by supplying an appropriate ‘qSupported’ feature (see qSupported). The remote stub must also supply the appropriate ‘qSupported’ feature indicating support.

vfork

The packet indicates that vfork was called, and r is the thread ID of the new child process, as specified in thread-id syntax. This packet is only applicable to targets that support vfork events.

This packet should not be sent by default; older GDB versions did not support it. GDB requests it, by supplying an appropriate ‘qSupported’ feature (see qSupported). The remote stub must also supply the appropriate ‘qSupported’ feature indicating support.

vforkdone

The packet indicates that a child process created by a vfork has either called exec or terminated, so that the address spaces of the parent and child process are no longer shared. The r part is ignored. This packet is only applicable to targets that support vforkdone events.

This packet should not be sent by default; older GDB versions did not support it. GDB requests it, by supplying an appropriate ‘qSupported’ feature (see qSupported). The remote stub must also supply the appropriate ‘qSupported’ feature indicating support.

exec

The packet indicates that execve was called, and r is the absolute pathname of the file that was executed, in hex. This packet is only applicable to targets that support exec events.

This packet should not be sent by default; older GDB versions did not support it. GDB requests it, by supplying an appropriate ‘qSupported’ feature (see qSupported). The remote stub must also supply the appropriate ‘qSupported’ feature indicating support.

clone

The packet indicates that clone was called, and r is the thread ID of the new child thread, as specified in thread-id syntax. This packet is only applicable to targets that support clone events.

This packet should not be sent by default; GDB requests it with the QThreadOptions packet.

create

The packet indicates that the thread was just created. The new thread is stopped until GDB sets it running with a resumption packet (see vCont packet). This packet should not be sent by default; GDB requests it with the QThreadEvents packet. See also the ‘w’ (see thread exit event) remote reply below. The r part is ignored.

W AA
W AA ; process:pid

The process exited, and AA is the exit status. This is only applicable to certain targets.

The second form of the response, including the process ID of the exited process, can be used only when GDB has reported support for multiprocess protocol extensions; see multiprocess extensions. Both AA and pid are formatted as big-endian hex strings.

X AA
X AA ; process:pid

The process terminated with signal AA.

The second form of the response, including the process ID of the terminated process, can be used only when GDB has reported support for multiprocess protocol extensions; see multiprocess extensions. Both AA and pid are formatted as big-endian hex strings.

w AA ; tid

The thread exited, and AA is the exit status. This response should not be sent by default; GDB requests it with either the QThreadEvents or QThreadOptions packets. See also thread create event above. AA is formatted as a big-endian hex string.

N

There are no resumed threads left in the target. In other words, even though the process is alive, the last resumed thread has exited. For example, say the target process has two threads: thread 1 and thread 2. The client leaves thread 1 stopped, and resumes thread 2, which subsequently exits. At this point, even though the process is still alive, and thus no ‘W’ stop reply is sent, no thread is actually executing either. The ‘N’ stop reply thus informs the client that it can stop waiting for stop replies. This packet should not be sent by default; older GDB versions did not support it. GDB requests it, by supplying an appropriate ‘qSupported’ feature (see qSupported). The remote stub must also supply the appropriate ‘qSupported’ feature indicating support.

O XX

XX’ is hex encoding of ASCII data, to be written as the program’s console output. This can happen at any time while the program is running and the debugger should continue to wait for ‘W’, ‘T’, etc. This reply is not permitted in non-stop mode.

F call-id,parameter

call-id is the identifier which says which host system call should be called. This is just the name of the function. Translation into the correct system call is only applicable as it’s defined in GDB. See File-I/O Remote Protocol Extension, for a list of implemented system calls.

parameter’ is a list of parameters as defined for this very system call.

The target replies with this packet when it expects GDB to call a host system call on behalf of the target. GDB replies with an appropriate ‘F’ packet and keeps up waiting for the next reply packet from the target. The latest ‘C’, ‘c’, ‘S’ or ‘s’ action is expected to be continued. See File-I/O Remote Protocol Extension, for more details.


Next: , Previous: , Up: Remote Protocol   [Contents][Index]